Revolution Lift 2018-01-10T16:08:24+00:00
Revolution Lifts - Carlisle, PA

Turner Hydraulics is the largest and most respected lift distributor in Pennsylvania, with above ground two-post, four-post, mid-rise vehicle and motorcycle service lifts for repair facilities and homeowner shops.

 

RTP10
The Revolution Lift RTP10 is a commercial grade 10,000 lbs. capacity 2 post lift. The RTP10 allows a customer to lift a vehicle either symmetrically or asymmetrically. It comes with a free set of adapter extensions (mounting hardware optional).”

Features:

  • Overhead padded switch bar to avoid vehicle damage from being
  • raised too high
  • 3-Stage front arm design enables you to position vehicle doors in front of or behind columns to avoid door damage
  • Top mounted pull design hydraulic cylinder. The piston rod is protected behind the carriage to prevent damage
  • Overhead cable equalization
  • Spring operated arm restraints, disengage at floor level
  • Single point lock release
  • Two full-stroke cylinders with overhead cable for equalization
  • Large rubber-padded swivel adapters with extra height extensions – Optional truck adapters are available.
  • ALI Certified

Specifications:

  • Capacity 10,000 lbs.
  • Rise 77″
  • Overall Height 143-1/8″
  • Overall Width 131″ (optional 137″)
  • Drive Through Clearance 97″ (optional 103″)
  • Overhead Switch Height 136-1/4″
  • Front Arm Reach (Min/Max) 23″ / 44-1/2″
  • Rear Arm Reach (Min/Max) 38-7/8″ / 58″
  • Min. Adapter Height 3-5/8″ / 10″
  • Width Inside Columns 109-3/4″ (optional 115-3/4″)
  • Voltage/Amps 208/230, 20 Amps
  • Motor / Phase 2 HP / 2 HP / 10*
  • Min. Ceiling Height 144″
 

R10The R10 features 3-stage front arms and 2-stage rear arms – greater access to vehicle pickup points!

The Revolution Lift R10 is a no nonsense straightforward two post lift that’s engineering surpasses that of other comparable lifts.  A garage or small shop with the R10 will get a 10,000-pound lift that’s affordable and dependable.  This is a symmetrical lift, which means you’ll be able to drive through with plenty of clearance.  The multiple stage arms give you additional options for vehicle pickup points. 

Hydraulic cylinders are housed in column from above and pull the arm carriage upward.  This means the cylinders are always protected from the grit and grime that could possibly make their way into this area.  Cables are there for equalization, they provide no load bearing, it’s the cylinders and locks within the column that do all the heavy work with this lift.

Features:

  • Full stroke hydraulic cylinders in each column
  • Top mounted pull design cylinder protects piston inside of carriage
  • Overhead cable for equalization
  • Spring operated arm restraints, disengage at floor level
  • Padded overhead switch bar
  • Single point lock release
  • ALI Gold Certified Lift

Specifications:

  • Capacity: 10,000lbs
  • Overall Height: 143-1/8″ (3642mm)
  • Height to Shut-Off: 137-34″ (3499mm)
  • Minimum Ceiling Height: Minimum Ceiling Height144″ (3658mm)
  • Minimum Adapter Height (standard adapters): 3-5/8″ (93mm)
  • Maximum Lifting Height: 76″ (1930mm)
  • Overall Floor Width: 137″ (3480mm) or optional 131″ (3327mm)
  • Inside Column Width: 115″ (2921mm)or optional 109″ (2769mm)
  • Drive Through: 105″ (2667mm) or optional 99″ (2515mm)
  • Adapter Heights: 3-1/2″and 5″
  • Voltage: 208v / 230v
  • Amps: 20
  • Motor: 2HP

RTP9The Revolution Lift RTP9 is a 9,000 lbs. capacity symmetric 2 post lift. The RTP9 is one of the most popular automotive lifts we sell. It comes with a free set of adapter extensions and all of the mounting hardware.

Features:

  • 9,000 lbs. capacity lift for facilities with low ceilings
  • Dual hydraulic cylinders with chains
  • Carriage latch system engages every 3″
  • Secondary lock system includes a spring actuated slack
  • chain locking device
  • Adapter extensions included
  • ALI Certified

Specifications:

  • Capacity 9,000 lbs.
  • Rise w/ Extensions 80-1/2″
  • Rise w/out Extensions 72″
  • Overall Height 111-1/4″
  • Overall Width 138-1/2″
  • Drive Through Clearance 97-1/4″
  • Width Inside Columns 111″
  • Arm Reach (Min/Max) 30″ / 46-1/4″
  • Min. Adapter Height 4.5″
  • Driver-Over Height 1-1/2″
  • Voltage/Amps 208/230, 20 Amps
  • Motor 2 HP
  • Min. Ceiling Height 113″ (9′-5″)
 

RTP12The Revolution Lift RTP12 is a commercial grade 12, 000 lbs. capacity 2 post lift. It comes with large rubber-padded swivel adapters with extra height extensions.

Features:

  • 12,000 lbs. capacity for raising most passenger cars, trucks and vans.
  • Hydraulic cylinders in each column, Full Stroke, Cylinder rod concealed inside carriage
  • Overhead cable equalization
  • Single Point lock release
  • Large rubber-padded swivel adapter with extra height extensions (4-1/2″ and 8-1/2″) are standard
  • Spring operated arm restraints, disengage at floor level
  • Padded overhead height limit switch bar
  • ALI Certified

Specifications:

  • Capacity 12,000 lbs.
  • Rise 82-1/2″ with adapters
  • Adjustable Overall Height 165-1/4″ / 177″ (high setup)
  • Overall Width 150-3/8″
  • Drive Through Clearance 109-1/2″
  • Overhead Switch Height 159-3/8″ low / 169-1/2″ high
  • Front Arm Reach (Min/Max) 38-1/2″ / 57-1/2″
  • Rear Arm Reach (Min/Max) 38-1/2″ / 57-1/2″
  • Lifting Pad Height 6″ / 10-1/2″ w/short extension / 14-1/2″ w/high extension
  • Width Inside Columns 123-1/4″
  • Voltage/Amps 208/230, 20 Amps
  • Motor 2 HP / 2 HP / 10* *optional 3-phase available
  • Speed of Rise 60 seconds

R12Greater lifting capacity for servicing cars, trucks and vans

The Revolution R12 is a value priced commercial grade 2-post lift. The ample 12,000-pound capacity ensures your shop can lift whatever comes through its doors.  Easy to swing 2-stage front and rear arms feature spring operated restraints that disengage at floor level.  Solidly built carriages handle the push from two full stroke cylinders all wrapped up in beefy columns designed for trouble-free performance.

Adjustable height and width options are available at installation to further customize your shop to its needs. It’s durable powder coated paint finish will stand up to the rigors of everyday use. It’s ALI certified, which means that it’s been third party tested and validated to perform against the ANSI/ALI ALCTV-2011 standard, giving you piece of mind.

Specifically designed frame engaging adapters that swivel to reach a vehicle’s recommended pick up points, are included with every lift. Studded rubber pads in the center of each adapter grip pinch weld pickup points. Each lift includes 3.5” and 5” adapter extensions are included with every lift. A storage bracket for the adapter extensions is included and can be positioned on each column.

Features:

  • 2-stage front and rear arms
  • Two full-stroke cylinders
  • Spring operated arm restraints, disengage at floor level
  • Adjustable overhead heights available*
  • Adjustable width and drive-thru settings
  • Padded overhead switch bar
  • Single point lock release
  • Frame-engaging swivel adapters – extra height extensions are standard
  • Durable powder coat finish
  • ALI Gold Certified Lift

Specifications:

  • Capacity 12,000 lbs. (5443kg)
  • Rise – Maximum Rise 72 -3/4” (1848mm) 77-3/4” (1975mm) w/ 5” adapter extension
  • Adjustable Overall Height Options
  • 166” (4216mm) Standard Height
  • 178” (4521mm) Extended Max. Height*
  • 154” (3912mm) LH1
  • 143” (3632mm) DP
  • Overall Width 140” or optional 146” (3556 / 3708mm)
  • Drive Through Clearance 102-3/4” or optional 108-3/4” (2609 / 2762mm)
  • Overhead Switch Height Options
  • 160-1/8” (4067mm) Standard
  • 172-1/8” (4524mm) Extended*
  • 148-1/8” (3762mm) LH1
  • 137-1/8” (3483mm) DP
  • Front Reach (Min./Max.) 35”/ 54” (889 / 1372mm)
  • Rear Reach (Min./Max.) 35”/ 54” (889 / 1372mm)
  • Min./Max. Adapter Height
  • 4-3/4” (120) w/ no adapter extension
  • 9-3/4” (248mm) w/ 5” adapter extension
  • Width Inside Column 120-7/8” (3070mm) Standard 114-7/8” (2918) Optional
  • Voltage/Amps 208/230, 12 amps; 208/230, 16 amps
  • Motor/Phase** 1ph**/2HP/50Hz; 1ph**/2HP/60Hz
  • Ceiling Height Required 168” (4267mm)
  • *Hose and cable kit required **Optional 3-phase available

RFP14The RFP14 is a commercial grade, four post lift that is perfect for any car and truck up to 14,000 lbs. The RFP14 incorporates a single point latch release system on its locks.

Features:

  • 5″ higher rise to 78.75″
  • Powder Coated Hammer Tone paint finish
  • Hydraulic cylinder placed under runway and out of the way
  • Multi-position locks allow runways to be level at any lock position
  • Single point lock release
  • Air latch and power unit controls located on front of column
  • ALI Certified

Specifications:

  • Capacity 14,000 lbs.
  • Rise 78-3/4″
  • Overall Length 18′-9″
  • Maximum Wheelbase 182″
  • Overall Width 11′-1″
  • Overall Height 6′-10 1/8″
  • Width Inside Columns 117-1/2″
  • Length Between Columns 189-1/4″
  • Runway Treadwidth 20″
  • Width Between Runways 43″
  • Runway Height 7″
  • Rise Time 55 seconds
  • Voltage/Amps 208/230, 20 amps
  • Motor 2 HP

RFP8Double Your Parking Space Instantly!

The RFP8 is the perfect solution if your garage is tight on space.  Removable ramps and multi-position locks add even more flexibility when space and overhead clearance is a concern. 

Features:

  • 72-1/2″ Lifting Height with 68” under runway clearance
  • Single point lock release
  • Adjustable lock ladder allow runways to be level at any lock position
  • Multi-position locks gives the convenience of working at any height
  • Standard 115V power
  • Includes:
    • Three (3) Drip Trays
    • One (1) Jack Tray Included – For use with hydraulic bottle jack
    • Polymer Caster Kit Included – for moving lift around when unloaded

The Revolution RFP8 is quality tested, third-party certified and value priced for your personal storage or independent repair use. 

The RFP8 is the most versatile tool in your garage. Use it to store your classics or your daily driver and your project car. With the optional platform kit, you can easily store lawnmowers, ATVs, jet skis or motorcycles. The possibilities are endless and it’s a whole lot less expensive than building a new garage. Don’t want to stack your vehicles? No problem. With multiple locking positions and clear center access and the included caster kit you can work on your car at any height and nearly anywhere in your garage. You won’t know what you did without it!

Specifications:

  • Capacity 8,000 lbs. (3629kg)
  • Rise 72-1/2” (1842mm)
  • Overall length with approach ramps 207-1/2” (5270mm)
  • Overall length without approach ramps 175 -1/2” (4458mm)
  • Overall width w/o motor 103 -1/2” (2629mm)
  • Approach ramp Length 32” (813mm)
  • Runway width 18 -1/2” (470mm)
  • Runway length 169 -1/2” (4305mm)
  • Runway height 4 -1/2” (114mm)
  • Height of columns 81 -1/2” (2070mm)
  • Clearance between columns 94” (2388mm)
  • Clearance between runways 38” (965mm)
  • Outside runway to outside runway 75” (1905mm)
  • Clearance under runway 68” (1727mm)
  • Motor specs 110VAC, 1HP

RFP9The RFP9 is a powerful, commercial grade, four post lift that is the perfect tool to help increase the amount of parking space without having to resort to costly construction. You can double your parking space instantly, by using the RFP9 parking lift in your shop or home.

Features:

  • Multi-position locks allow runways to be level at any lock position
  • Single point lock release
  • 9,000 lbs. capacity makes the RFP9 perfect for home use
  • ALI Certified
  • INCLUDES Steel approach ramps
  • INCLUDES Caster kit
  • INCLUDES One jack tray
  • INCLUDES Three drip trays

Specifications:

  • Capacity 9,000 lbs.
  • Lifting Height 84″
  • Ceiling Height to be height of highest vehicle to be raised plus 84″
  • Overall Length w/ Approach Ramps 225-1/2″
  • Overall Length w/out Approach Ramps 193-1/8″
  • Overall Width w/ Motor 131″
  • Overall Width w/out Motor 121-1/2″
  • Approach Ramp Length 36-1/4″
  • Runway Tread Width 21-3/4″
  • Runway Length 184-1/2″
  • Runway Height 4-3/4″
  • Height of Columns 97″
  • Clearance Between Columns 109-1/2″
  • Width Between Runway Treads 39″
  • Outside Runway to Outside Runway 79-1/2″
  • Clearance Under Runways 79-1/4″
  • Drive Through Width 97″
  • Height of Columns 97″
  • Power Unit 110 Volt , 1HP – (220 Volt Optional)
  • Shipping Weight 2,350 lbs.

RMR6The RMR6 is a portable mid rise hydraulic lift with a weight capacity of 6,000 lbs. The RMR6 is an excellent choice for any body shop. It is also popular with customers that do not have the ceiling clearance for a two post car or truck lift, or prefer something portable. The RMR6 comes with a free set of truck adapters.

Features:

  • Full 6,000 lbs. capacity
  • Portable and easy to move
  • Two hydraulic cylinders
  • Multiple locking positions at any height
  • INCLUDES Truck adapters

Specifications:

  • Capacity 6,000 lbs.
  • Rise 54″
  • Min. Height 5″
  • Length 83″
  • Width 41″
  • Power Unit 110 Volt
  • Shipping Weight 1,000 lbs.

RXLDTThe RXLDT comes with two 12” side extensions, a wheel vise and dolly. The RXLDT is an excellent choice for anyone looking to service ATVs, motorcycles, or anything else that will fit on the 93” long x 48” wide table.

Features:

  • Front wheel vise prevents wheel movement during securing,
  • lifting and maintenance
  • Foot pedal controlled power unit operates on 100 PSI air
  • Rear section (drop tail) is removable for complete rear wheel access
  • Side extensions are standard for ATV and additional vehicle service

Specifications:

  • Capacity 1,000 lbs.
  • Rise 33″
  • Min. Height 7-1/4″
  • Length w/ Ramp 113″
  • Length w/out Ramp 93″
  • Width of Platform 24″
  • Width w/ ATV Adapters 48″
  • Air Requirements 90-100 PSI
  • Shipping Weight 690 lbs.

Lift Accessories

Drip Tray

Details:

  • Additional Plastic Drip Tray

90° Power Unit Bracket

Details:

  • To move power unit to front of column for additional space.

Details:Solid Deck Flooring Panel

  • Flooring Panel for RFP9 Lift to convert lift to solid deck for storage.
  • Panels are 37″ wide X 20″ long
  • Requires 8 per lift
  • 330 lb. capacity

Drive-thru RampsDetails:

  • 36.5″ long Drive-thru Ramp (2 Required)
  • Designed for RFP9 4-post lift only

Jack Tray/Parts BoxDetails:

Internal Air KitDetails:

  • The Internal Air Kit is designed for RFP14 4-post lift only

Carbon Steel Radius GaugeDetails:

  • 1 individual carbon steel radius gauge (2 required)

Drive-thru Ramps for RFP14Details:

  • 51″ long Drive-thru Ramps (set of 2)
  • Designed for RFP14 4-post lift only

4,500 LB Rolling JackDetails:

  • Manual operation – no air required
  • Comes with two 1.25″ and two 5″ adapter extensions
  • Designed for the RFP9 4-Post lift

Bolt-On Runway Extension KitDetails:

  • 2 foot bolt-on runway extension kit for RFP14 (4-post) and RFPAR14 lifts

7,000 LB Rolling JackDetails:

  • Comes with two 3″ and two 6″ adapter extensions
  • Designed for the RFP14 4 Post lift

Belt-On Alignment KitDetails:

  • Bolt-on Kit to convert RFP14 (4-post) to alignment rack
  • (radius gauge not included)

Request A Quote: